The contribution of floor bearing plate in steel structure engineering is obvious to all, especially the advantages of wide application range and fast construction speed of floor bearing plate, which has established its position in the field of steel structure. Now let's talk about how to solve the quality problems in Jinan floor bearing plate construction.

1.幾何尺寸偏差和運輸損傷

1. Geometric dimension deviation and transportation damage

這兩個問題主要出現在加工過程中，因此，在樓承板開始生產加工之前，安排人員對加工工藝、外觀和尺寸進行檢測，符合要求之后再開始批量生產。對于尺寸偏差超過要求的，或在運輸途中受到損傷的構件，輕微損傷現場維修，損傷嚴重的，應進行退回返修或換新。樓承板廠家認為，這是一家負責任的企業應該承擔的責任。

These two problems mainly occur in the processing process. Therefore, before the production and processing of the floor bearing plate, arrange personnel to inspect the processing technology, appearance and size, and start batch production after meeting the requirements. For components with dimension deviation exceeding the requirements or damaged during transportation, minor damage shall be repaired on site, and those with serious damage shall be returned for repair or replaced. The floor bearing plate manufacturer believes that this is the responsibility of a responsible enterprise.

2.邊角板變形

2. Corner plate deformation

在運輸過程中沒有妥當采取保護措施是造成邊角板變形的主要原因。樓承板廠家建議：在樓承板下方鋪設墊板，用打包帶或專門的角鋼包裝架捆扎，在周圍做好柔性防護并且確保固定穩妥，便可防止構件之間的損傷。

The main reason for the deformation of the corner plate is that the protective measures are not properly taken during transportation. The manufacturer of the floor bearing plate suggests that: lay a base plate under the floor bearing plate, bind it with a packing belt or a special angle steel packing frame, provide flexible protection around it and ensure that it is firmly fixed, so as to prevent damage between components.

3.點焊脫開

3. Spot welding separation

這里說的“點焊脫開”是桁架筋和鍍鋅板連接的焊接部分，這個問題主要是由于桁架鋼筋直徑較粗，打彎不到位，導致虛假點焊。避免這個問題，需要從源頭出發，會對桁架鋼筋彎曲設備進行調試，以確保彎曲成型的準確度。

The "spot welding separation" here refers to the welding part of the connection between the truss reinforcement and the galvanized plate. This problem is mainly due to the thick diameter of the truss reinforcement and the failure to bend it in place, which leads to false spot welding. To avoid this problem, we need to start from the source and debug the truss reinforcement bending equipment to ensure the accuracy of bending and forming.

另外，還應加強焊接部分的質量檢查。樓承板廠家通常的處理措施：如果是局部點焊脫開可進行現場復焊；如果情況較為普遍，就須返回處理。值得一提的是：如果點焊處的鍍鋅板有穿孔現象，應對穿孔部位用膠封堵，另外，考慮到是焊接電流過大的問題，因此應對施焊電流進行調試。

In addition, the quality inspection of welding parts shall be strengthened. Common treatment measures of floor bearing plate manufacturer: if it is local spot welding separation, conduct on-site re welding; If the situation is more common, it must be returned for processing. It is worth mentioning that if the galvanized sheet at the spot welding point has holes, the holes should be sealed with glue. In addition, considering the problem of excessive welding current, the welding current should be adjusted.

按照規定，材料在進場前需要進行再次復核，通常會出問題的地方，以上就是問題的相關解答了，您對此有什么內容就來我們網站http://m.xpj55507.com咨詢吧！

According to the regulations, the materials need to be rechecked again before entering the site. The above is the answer to the question. Please come to our website if you have any information about it http://m.xpj55507.com Consult!